glacial landform

Types of glaciers

There are numerous types of glaciers, but it is sufficient here to focus on two broad classes: mountain, or valley, glaciers and continental glaciers, or ice sheets, (including ice caps). For information about other types, see the articles ice and glacier.

Generally, ice sheets are larger than valley glaciers. The main difference between the two classes, however, is their relationship to the underlying topography. Valley glaciers are rivers of ice usually found in mountainous regions, and their flow patterns are controlled by the high relief in those areas. In map view, many large valley glacier systems, which have numerous tributary glaciers that join to form a large “trunk glacier,” resemble the roots of a plant. Pancakelike ice sheets, on the other hand, are continuous over extensive areas and completely bury the underlying landscape beneath hundreds or thousands of metres of ice. Within continental ice sheets, the flow is directed more or less from the centre outward. At the periphery, however, where ice sheets are much thinner, they may be controlled by any substantial relief existing in the area. In this case, their borders may be lobate on a scale of a few kilometres, with tonguelike protrusions called outlet glaciers. Viewed by themselves, these are nearly indistinguishable from the lower reaches of a large valley glacier system. Consequently, many of the landforms produced by valley glaciers and continental ice sheets are similar or virtually identical, though they often differ in magnitude. Nonetheless, each type of glacier produces characteristic features and thus warrants separate discussion.

Glacial erosion

Two processes, internal deformation and basal sliding, are responsible for the movement of glaciers under the influence of gravity (see glacier). The temperature of glacier ice is a critical condition that affects these processes. For this reason, glaciers are classified into two main types, temperate and polar, according to their temperature regime. Temperate glaciers are also called isothermal glaciers, because they exist at the pressure-melting point (the melting temperature of ice at a given pressure) throughout their mass. The ice in polar, or cold glaciers, in contrast, is below the pressure-melting point. Some glaciers have an intermediate thermal character. For example, subpolar glaciers are temperate in their interior parts, but their margins are cold-based. This classification is a broad generalization, however, because the thermal condition of a glacier may show wide variations in both space and time.

Internal deformation, or strain, in glacier ice is a response to shear stresses arising from the weight of the ice (ice thickness) and the degree of slope of the glacier surface. Internal deformation occurs by movement within and between individual ice crystals (slow creep) and by brittle failure (fracture), which arises when the mass of ice cannot adjust its shape rapidly enough by the creep process to take up the stresses affecting it. The relative importance of these two processes is greatly influenced by the temperature of the ice. Thus, fractures due to brittle failure under tension, known as crevasses, are usually much deeper in polar ice than they are in temperate ice.

Explore Britannica Premium!

The trusted destination for professionals, college students, and lifelong learners.

SUBSCRIBE

The temperature of the basal ice is an important influence upon a glacier’s ability to erode its bed. When basal temperatures are below the pressure-melting point, the ability of the ice mass to slide on the bed (basal sliding) is inhibited by the adhesion of the basal ice to the frozen bed beneath. Basal sliding is also diminished by the greater rigidity of polar ice: this reduces the rate of creep, which, in turn, reduces the ability of the more rigid ice to deform around obstacles on the glacier bed. Thus, the flow of cold-based glaciers is predominantly controlled by internal deformation, with proportionately low rates of basal sliding. For this reason, rates of abrasion are commonly low beneath polar glaciers, and slow rates of erosion commonly result. Equally, the volume of meltwater is frequently very low, so that the extent of sediments and landforms derived from polar glaciers is limited.

Temperate glaciers, being at the pressure-meeting point, move by both mechanisms, with basal sliding being the more important. It is this sliding that enables temperate glaciers to erode their beds and carve landforms so effectively. Ice is, however, much softer and has a much lower shear strength than most rocks, and pure ice alone is not capable of substantially eroding anything other than unconsolidated sediments. Most temperate glaciers have a basal debris zone from several centimetres to a few metres thick that contains varying amounts of rock debris in transit. In this respect, glaciers act rather like sheets of sandpaper; while the paper itself is too soft to sand wood, the adherent hard grains make it a powerful abrasive system. The analogy ends here, however, for the rock debris found in glaciers is of widely varying sizes—from the finest rock particles to large boulders—and also generally of varied types as it includes the different rocks that a glacier is overriding. For this reason, a glacially abraded surface usually bears many different “tool-marks,” from microscopic scratches to gouges centimetres deep and tens of metres long. Over thousands of years glaciers may erode their substrate to a depth of several tens of metres by this mechanism, producing a variety of streamlined landforms typical of glaciated landscapes.

Several other processes of glacial erosion are generally included under the terms glacial plucking or quarrying. This process involves the removal of larger pieces of rock from the glacier bed. Various explanations for this phenomenon have been proposed. Some of the mechanisms suggested are based on differential stresses in the rock caused by ice being forced to flow around bedrock obstacles. High stress gradients are particularly important, and the resultant tensile stresses can pull the rock apart along pre-existing joints or crack systems. These pressures have been shown to be sufficient to fracture solid rock, thus making it available for removal by the ice flowing above it. Other possibilities include the forcing apart of rock by the pressure of crystallization produced beneath the glacier as water derived from the ice refreezes (regelation) or because of temperature fluctuations in cavities under the glacier. Still another possible mechanism involves hydraulic pressures of flowing water known to be present, at least temporarily, under nearly all temperate glaciers. It is hard to determine which process is dominant because access to the base of active glaciers is rarely possible. Nonetheless, investigators know that larger pieces of rock are plucked from the glacier bed and contribute to the number of abrasive “tools” available to the glacier at its base. Other sources for the rock debris in glacier ice may include rockfalls from steep slopes bordering a glacier or unconsolidated sediments overridden as a glacier advances.