The isoquants also illustrate an important economic phenomenon: that of factor substitution. This means that one variable factor can be substituted for others; as a general rule a more lavish use of one variable factor will permit an unchanged amount of output to be produced with fewer units of some or all of the others. In the example above, labour was literally as good as gold and could be substituted for it. If it were not for factor substitution there would be no room for further decision after y, the number of chains to be produced, had been established.
The shape of the isoquants shown, for which there is a good deal of empirical support, is very important. In moving along any one isoquant, the more of one factor that is employed, the less of the other will be needed to maintain the stated output; this is the graphic representation of factor substitutability. But there is a corollary: the more of one factor that is employed, the less it will be possible to reduce the use of the other by using more of the first. This is the property known as âdiminishing marginal rates of substitution.â The marginal rate of substitution of factor 1 for factor 2 is the number of units by which x 1 can be reduced per unit increase in x, output remaining unchanged. In the diagram, if feet of gold wire are indicated by x 1 and goldsmith-hours by x 2, then the marginal rate of substitution is shown by the steepness (the negative of the slope) of the isoquant; and it will be seen that it diminishes steadily as x 2 increases because it becomes harder and harder to economize on the use of gold simply by taking more care. The remainder of the analysis rests heavily on the assumption that diminishing marginal rates of substitution are characteristic of the production process generally.
Figure 2: Isoquant diagram for two factors of production, x1 and x2 (see text).
EncyclopĂŠdia Britannica, Inc.
The cost data and the technological data can now be brought together. The variable cost of using x 1, x 2 units of the factors of production is written p 1 x 1 + p 2 x 2, and this information can be added to the isoquant diagram (Figure 2). The straight line labelled v 2, called the v 2-isocost line, shows all the combinations of input that can be purchased for a specified variable cost, v 2. The other two isocost lines shown are interpreted similarly. The general formula for an isocost line is p 1 x 1 + p 2 x 2 = v, in which v is some particular variable cost. The slope of an isocost line is found by dividing p 2 by p 1 and depends only on the ratio of the prices of the two factors.
Three isocost lines are shown, corresponding to variable costs amounting to v 1, v 2, and v 3. If 200 units are to be produced, expenditure of v 1 on variable factors will not suffice since the v 1-isocost line never reaches the isoquant for 200 units. An expenditure of v 3 is more than sufficient; and v 2 is the lowest variable cost for which 200 units can be produced. Thus v 2 is found to be the minimum variable cost of producing 200 units (as v 3 is of 300 units) and the coordinates of the point where the v 2 isocost line touches the 200-unit isoquant are the quantities of the two factors that will be used when 200 units are to be produced and the prices of the two factors are in the ratio p 2/p 1. It may be noted that the cheapest combination for the production of any quantity will be found at the point at which the relevant isoquant is tangent to an isocost line. Thus, since the slope of an isoquant is given by the marginal rate of substitution, any firm trying to produce as cheaply as possible will always purchase or hire factors in quantities such that the marginal rate of substitution will equal the ratio of their prices.
The isoquantâisocost diagram (or the corresponding solution by the alternative means of the calculus) solves the short-run cost minimization problem by determining the least-cost combination of variable factors that can produce a given output in a given plant. The variable cost incurred when the least-cost combination of inputs is used in conjunction with a given outfit of fixed equipment is called the variable cost of that quantity of output and denoted VC(y). The total cost incurred, variable plus fixed, is the short-run cost of that output, denoted SRC(y). Clearly SRC(y) = VC(y) + R(K), in which the second term symbolizes the sum of the annual costs of the fixed factors available.
Two other concepts now become important. The average variable cost, written AVC(y), is the variable cost per unit of output. Algebraically, AVC(y) = VC(y)/y. The marginal variable cost, or simply marginal cost [MC(y)] is, roughly, the increase in variable cost incurred when output is increased by one unit; i.e., MC(y) = VC(y + 1) - VC(y). Though for theoretical purposes a more precise definition can be obtained by regarding VC(y) as a continuous function of output, this is not necessary in the present case.
Figure 3: Average variable costs (AVC) and marginal variable costs (MC) in relation to output.
EncyclopĂŠdia Britannica, Inc.
The usual behaviour of average and marginal variable costs in response to changes in the level of output from a given fixed plant is shown in Figure 3. In this figure costs (in dollars per unit) are measured vertically and output (in units per year) is shown horizontally. The figure is drawn for some particular fixed plant, and it can be seen that average costs are fairly high for very low levels of output relative to the size of the plant, largely because there is not enough work to keep a well-balanced work force fully occupied. People are either idle much of the time or shifting, expensively, from job to job. As output increases from a low level, average costs decline to a low plateau. But as the capacity of the plant is approached, the inefficiencies incident on plant congestion force average costs up quite rapidly. Overtime may be incurred, outmoded equipment and inexperienced hands may be called into use, there may not be time to take machinery off the line for routine maintenance; or minor breakdowns and delays may disrupt schedules seriously because of inadequate slack and reserves. Thus the AVC curve has the flat-bottomed U-shape shown. The MC curve, as might be expected, falls faster and rises more rapidly than the AVC curve.
